Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Grapevine
If your driveway gate is sagging, dragging, or torn loose at the hinge, the fix usually comes down to two things: the right part and a weld that’s actually strong enough to hold. Gate parts and welding in Grapevine is the service we run calls for every week, from ornamental iron driveway gates in Silverlake to commercial slide gates along SH-114. We stock the common hinge barrels, ball-bearing hinges, rollers, and latch hardware right on our trucks, so most repair calls get finished in one visit and the gate works like it should that same day. Call us at (817) 580-8494 and we’ll have a tech out to you fast.
Why Ironworks Gate Co. Is Grapevine’s Preferred Gate Parts & Welding Company
We’re not a general handyman service that does gates on the side. We only do gates. That narrow focus shows up in how we work in Grapevine: we know which hinge style fits the ornamental iron common in Stone Bridge Oaks, we know which post footings hold in the clay along Grapevine Lake, and we know what an HOA architectural committee is going to ask before the work starts. Our techs carry parts for LiftMaster, FAAC, and Mighty Mule as a standard loadout, and every one of them welds with a steady, repeatable process so the repair doesn’t have to be redone in two years.
Every job is backed by our 90-Day Done Right Promise, in writing. If the part or the weld isn’t right, we come back and make it right. No paperwork and no arguing. That’s the Keystone Standard we’ve used on every gate job since 1984, and it applies to every hinge we hang and every bead we run in the 76051 and 76099 zip codes.
We also answer the phone. A live person picks up 24 hours a day, 7 days a week, so when a gate won’t open for a service vehicle at 6 a.m. before a flight out of DFW, you get a person, not voicemail.
Our Gate Parts & Welding Services in Grapevine
Most of what we do comes down to replacing the part that wore out, or welding the piece that broke. We cover the full scope of Gate Parts & Welding for single-family homes, HOA-managed entries, and commercial properties around DFW Airport. Here are the four services we run most in Grapevine.
Hinge Replacement
A gate hinge carries the entire weight of the gate leaf, every time it opens, every day of the year. When a hinge pin wears out or the barrel elongates, the gate drops at the latch side and starts dragging. In Grapevine, this is the single most common gate call we get. We carry heavy-duty ball-bearing hinges in the common sizes for ornamental iron gates, and if your existing hinge was welded on, we cut it out, dress the post, and weld the new one in place with a full-penetration weld that holds.
Post Replacement
North Texas black clay shrinks during dry stretches and swells back after rain. That movement works gate posts loose over time, especially on sloped or lakefront lots. We reset posts in deep sonotube footings with proper concrete and let the concrete cure for 30 minutes with bracing before re-hanging the gate. A post that’s truly rusted through or broken at the base gets cut off at grade and replaced with a new schedule 40 steel post, welded or bolted as the gate design requires.
Rail Repair
When a top or bottom rail snaps, the gate loses structural integrity and it’s only a matter of time before the whole frame twists. We weld the broken rail back with proper joint prep, or we’ll sleeve it from behind so there’s more weld surface than the original. For gates that have already been repaired a few times, we sometimes recommend replacing the entire rail section instead of stacking another patch on top of the last one. Either way, the price is set before we strike an arc.
Custom Welding
Some gates can’t be fixed with a replacement part because the part doesn’t exist anymore, or the gate was built in place and nothing off-the-shelf matches. That’s where our custom welding comes in. We fabricate pickup pockets, receiver hitches for slide gates, extra bracing for wide swing gates, lock boxes, custom latch brackets, and steel panel infill to match the surrounding ironwork. We’ve done this enough in Grapevine’s older Main Street district to match period ironwork on homes from the early 20th century, and we weld to the original gate’s style so the repair doesn’t look like an add-on.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Grapevine
When a gate operator fails, the problem is often a worn part or a bad wire, not the whole motor. We service operators from LiftMaster, FAAC, Elite, Mighty Mule, and the other major brands on the market, and we stock the part numbers that fail most in our climate: motor capacitors, limit switches, and control board fuses. That means the repair usually happens on the first visit and you don’t wait a week for a board to ship. If your operator is still under manufacturer warranty, we coordinate the parts claim so you aren’t paying for a component that should be covered.
Common Gate Parts & Welding Problems We See in Grapevine Homes
We have run enough calls across Grapevine to know what fails here, and what does not. These are the patterns, specific to this area:
- Hinge posts leaning out of plumb. Black clay soil in the 76051 and 76099 areas shrinks in the summer drought cycles, especially on lakefront and hillside lots, and the post effectively loses its footing. The gate then binds at the latch and drags across the concrete.
- HOA architectural rejection. Several of Grapevine’s master-planned communities, including Silverlake and Stone Bridge Oaks, have architectural committees that govern gate style, height, and finish. If a welded replacement panel or post doesn’t match the approved look, the committee will flag it and hold up the close of the job. This is a local reality that flat-lot installers miss.
- Worn hinge barrels on older ornamental gates. The 1980s and 90s subdivisions around Grapevine are full of ornamental iron gates that are 30 to 40 years old now, and the hinge barrels are reaching the end of their service life. A barrel that has wallowed out causes the gate to sag, and eventually the latch no longer lines up.
- Shared entry gate failures. Gated communities with a single shared entrance depend on loop detectors and safety photocells that fall out of alignment or fail entirely. When that happens, the gate won’t stay open or refuses to cycle, and the HOA has a resident line of cars waiting at the keypad.
Pricing for Gate Parts & Welding in Grapevine, TX
We quote every gate job before we start and the price doesn’t change once the work begins. You agree to the number, then we turn the wrench or light the torch. Here’s what you’ll typically see in Grapevine as of this year:
| Service | Typical Range | Notes |
|---|---|---|
| Hinge replacement (pair, welded) | $240-$420 | Ball-bearing or standard barrel hinges, field welded |
| Post replacement (single) | $380-$750 | Includes new steel post, sonotube footing, concrete, re-hang |
| Rail repair (cracked or broken rail) | $160-$350 | Weld repair with joint prep and optional sleeve |
| Custom welding (bracket, gusset, small fab) | $120-$400 | Mobile welding at your property, no shop drop-off |
Those ranges cover a straight gate repair with standard parts. If we find rotted post bases, extensive rust, or a twisted frame, the price adjusts and we tell you the new number before doing the extra work. We don’t add on after the fact. We also offer a $50 discount on any repair over $250, a free second opinion on any written estimate from another company, and a permanent 5% discount for seniors and veterans. If you’re in Grapevine and the gate is down, call us and ask for a price to fix it; the estimate is free.
We Also Serve Cities Near Grapevine
Our crews run calls across the mid-cities every day. If you’re in Southlake, Colleyville, Coppell, or Euless, we serve those markets too. The same trucks, the same parts stock, and the same 90-Day Done Right Promise. If you’re outside Grapevine itself but still in the area, call and ask whether we’re scheduled in your neighborhood this week. Whether you’re in Grapevine or a nearby town, our Gate Parts & Welding in Grapevine team is the one to call.
Serving Grapevine, TX - Our Local Coverage Area
We’re based in the Grapevine area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Grapevine
Yes, in most HOA-governed Grapevine communities you do, and you need to start that approval before we start cutting steel. Silverlake, Stone Bridge Oaks, and other deed-restricted neighborhoods have committees that review gate style, height, and finish. We’ll provide a drawing or photo of the proposed panel, the materials list, and the finish spec so you can submit a complete application. If the committee wants changes, we adjust before we weld, not after. Call us at (817) 580-8494 and we’ll walk you through what the committee usually asks for.
It slowly pushes the post out of plumb. During the summer, the clay shrinks, leaves a void around the footing, and the gate’s weight then leans the post toward the latch side. After rain, the clay swells and pushes sideways. The gate starts to bind at the latch and the opening clearance goes away. The fix is resetting the post in a deeper sonotube with more concrete, not just shimming the hinge and hoping it holds. We’ve fixed this on enough lakefront and hillside lots in Grapevine to know the pattern by heart.
In most cases, yes. We commonly add bracing, gussets, or a longer weld run to an existing gate frame when the iron itself is still sound. It only becomes a case for replacement when the bottom rail is rusted through internally, or when the gate has been re-welded so many times that adding more metal creates new stress points. We’ll tell you which situation you have, and the reinforcement quote is typically less than half the cost of a new gate.
We replace the damaged rack section and often the pinion gear at the same time, because a bent rack usually damages the gear teeth that engage it. Running the operator on damaged teeth spreads the failure to the motor mount and drive chain. We stock common rack profiles and gear sizes for commercial slide gates on our trucks, so we can often have an airport-area gate cycling again the same day. Call (817) 580-8494 and we’ll quote the rack section replacement before we send a tech.
Yes, we do it regularly. We’ll speak with the property manager or the board member responsible for the gate, give them a written quote, and coordinate access so residents are not locked out during the repair. For shared entries, we commonly replace loop detectors, re-align safety photocells, and weld broken gate frames or reinforcement brackets. The price is agreed with the HOA in writing before we start, and we handle the work so the board doesn’t have to chase three different vendors.
If your gate is leaning, dragging, or the hinge finally let go, don’t rig it with a bungee cord and hope. Call Ironworks Gate Co. at (817) 580-8494. We’ll give you a straight answer, a straight price, and a repair that’s done right and backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Grapevine and the surrounding mid-cities area for over 42 years.