Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Hurst
Gate parts and welding in Hurst usually comes down to one of three jobs: a hinge that has finally worn out on a 50-year-old iron gate, a post that Tarrant County clay has pushed out of plumb, or a weld that cracked under daily use. We fix all three, and we do it with a written 90-Day Done Right Promise behind the work. If your gate drags, sags, or will not latch, call us at (817) 580-8494 for a free estimate, and we will be out to your Hurst home fast.
We are Ironworks Gate Co. We have been doing this work for over 42 years. We know the gates in Hurst’s 76053 and 76054 neighborhoods, and we know why they fail here.
Why Ironworks Gate Co. Is Hurst’s Preferred Gate Parts & Welding Company
Hurst homeowners call us because their gates were hung decades ago, and the companies that hung them are long gone. We are still here, and our Gate Installation - Hurst team works on original ornamental iron and chain-link gates from the mid-century ranch era every week. We have learned exactly how these particular gates wear. A gate that has swung on the same pintles since 1962 has a different set of problems than a gate hung last year, and we treat it accordingly.
Our team knows that one gate on a narrow Hurst side yard is often the only rear-yard access point on the entire property. When it fails, the whole backyard becomes unusable. That is why we schedule Hurst repairs quickly, and why a live person answers the phone 24 hours a day, 7 days a week, ready to take your call and get you on the schedule. You will never sit through a voicemail maze when your gate is stuck half-open.
Every Hurst customer gets the same treatment: background-checked, uniformed technicians who work in your yard the way they would work in their own mother’s. And every job, from a small hinge replacement to a full post reset and custom weld, is covered by our 90-Day Done Right Promise. It is a written guarantee. No paperwork, no arguing. If it is not right, we come back and make it right.
Our Gate Parts & Welding Services in Hurst
Hinge Replacement
On Hurst’s older gates, hinge replacement is rarely just swapping a bolt-on part. The pintles on a 1960s ornamental iron gate are often worn egg-shaped from decades of daily swings, which is what causes that sag-and-drag you feel when you push it open. We remove the old barrels, weld in new hinge assemblies sized for the original post, and set the gate back to clear its strike side cleanly. If the post itself has moved in the clay, we address that first, or the new hinge will wear out the same way.
Post Replacement
Gate posts across Hurst’s 76053 and 76054 ZIP codes sit in expansive clay that swells in wet springs and shrinks in baking summers. That movement pushes posts one to two inches out of plumb, and no amount of hinge shimming fixes it. We pull the old post, pour a new concrete footer at a depth that gets below the active clay zone, and re-set the post straight. This is a permanent fix, not a seasonal adjustment. We size the footing for the specific gate weight and swing radius, so the post holds through the next wet-dry cycle and every one after that.
Rail Repair
Wrought iron and chain-link gates take their structural load on the top and bottom rails, and once a rail bows, cracks, or pulls free of the frame, the whole gate loses its square. On Hurst ranch homes where the gate is the only side-yard access, that loss of square shows up as a gate that will not latch or scrapes against the drive. We straighten, sleeve, or replace damaged rails and weld them back into true alignment with the rest of the frame. If the original rail is too deteriorated to safely weld, we tell you honestly and fabricate a replacement section.
Custom Welding
Some repairs on older Hurst gates need metalwork that no shelf part fits. Original ornamental iron from the 1950s and 1960s was not built to modern dimensional standards, and a replacement hinge, extension plate, or latch bracket often has to be cut, shaped, and welded on-site. Our Gate Parts & Welding team fabricates custom brackets, rebuilds broken scrollwork, and welds cracked frame sections back together so the repair matches the gate instead of looking bolted on. We weld what can be saved, and we are square with you when it cannot.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Hurst
Hurst homes with automated gates often run equipment that has been out of production for a decade or more, and we keep parts and knowledge for the legacy systems still in service here. We work on LiftMaster, Elite, and Mighty Mule systems regularly, along with FAAC and five other major opener brands, so if your gate motor & opener in Hurst fails, we can usually bring the correct part on the first truck roll. For older control boards with no modern entrapment protection, we will show you the retrofit option and the replacement option, with honest numbers for both.
Common Gate Parts & Welding Problems We See in Hurst Homes
- Post heave after wet springs. Expansive clay under 76053 and 76054 pushes gate posts out of plumb seasonally, so a gate that latched perfectly in October suddenly binds in May. Post-reset is often the only real cure.
- Worn pintles and sagging panels. Fifty years of single-gate daily use wears the hinge pins thin, and the gate starts dragging on the strike side. This is not a panel failure, it is hinge metallurgy showing its age.
- Legacy operators with obsolete control boards. Many 1980s and 1990s gate motors around Hurst have boards that are no longer manufactured and no modern photo-eye or edge-sensor protection. We help you decide whether to retrofit or replace with current equipment.
- Out-of-square frames and broken welds. A gate that slams or catches the wind repeatedly will crack at the weld joints over time. Hairline cracks open into full breaks, and the gate loses its shape. We weld the frame back square before the crack propagates further.
Pricing for Gate Parts & Welding in Hurst, TX
A hinge replacement on a typical Hurst drive gate runs between $180 and $385, depending on whether the pintles are welded or bolt-on and whether one side or both sides need work. Post replacement, including demolition, a new footing below the active clay zone, and re-setting the gate, typically runs $550 to $1,300 per post. Custom welding jobs on ornamental iron gates fall between $150 and $600, depending on the extent of the fabrication. If we find legacy opener damage during a parts call, a retrofit control board typically runs $450 to $900, while a full operator replacement with modern entrapment protection starts around $1,100. Every price is quoted and agreed before any work starts, and we honor the written estimate to the dollar. Call (817) 580-8494 for a free estimate on your specific gate.
We Also Serve Cities Near Hurst
Ironworks Gate Co. serves the broader mid-cities area, including Bedford, North Richland Hills, Colleyville, and Euless. If you are looking for Gate Parts & Welding in Hurst, our local crews know every neighborhood from Precinct Line Road to the Pipeline Road corridor, and we get to your home quickly.
Serving Hurst, TX - Our Local Coverage Area
We’re based in the Hurst area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Hurst
Your gate posts have moved. The expansive clay soil common across Hurst swells when saturated, lifting and shifting the post one to two inches out of plumb in as little as a day. The gate and hinges are fine, but the geometry is now wrong, so it binds. The fix is a post reset with a deeper footing, not a hinge adjustment. Call (817) 580-8494 and we will confirm it before we touch anything.
In most cases we can retrofit. The original iron panels on Hurst’s 1950s and 1960s ranch homes are often heavier and better built than anything sold today, so we prefer to keep them. We check the hinge posts, the panel condition, and the gate weight, then match Gate Access Control in Hurst with a modern operator from LiftMaster, Elite, Mighty Mule, or FAAC to the existing gate. If the posts have heaved or the frame is cracked, we fix that first. The honest answer is that retrofit works about 80% of the time. We will tell you if yours is the exception before you spend a dollar.
You need hinge work. We see this constantly in Hurst, and the sag is nearly always worn pintles, not a failed panel. The original ornamental iron panels on mid-century Hurst homes are thick and solid, but the hinge barrels wear thin over 50 years. We replace or weld-new the hinge assemblies, re-set the gate square, and it swings like it did when it was hung. A full panel replacement is a much rarer conversation. Estimate for hinge replacement is free; call (817) 580-8494 and we will inspect yours.
For a standard drive gate post in Tarrant County clay, we set the concrete footer at a minimum of 30 to 36 inches deep, and deeper for heavy iron panels or gates over 8 feet wide. This puts the footing below the active clay zone where most seasonal expansion happens. If a post is not set that deep, it will eventually heave again. It is not a matter of if, it is a matter of which wet spring. We pull and reset posts to that depth on every post replacement in Hurst.
It is a post problem. When the clay dries and contracts, the post leans slightly, and the latch strike no longer meets the bolt. You can adjust the latch once to work around it, but the post will move again. The permanent fix is to pull the post and pour a proper footing below the active clay depth, then re-mount the latch in correct alignment. It costs more than a latch swap, but it is the last time you will have this conversation. Call (817) 580-8494 and we will quote the post work honestly.
Local Insight: Why Hurst Clay Makes Post-Reset a Near-Automatic Add-On
On a wet spring day, when the clay under Hurst has absorbed weeks of rain, we take calls from homeowners whose gates simply stopped closing. The hinge posts have moved. One to two inches of heave is enough to rack a gate frame against its latch post and make the gate bind or refuse to close. Our crews carry the equipment to dig, pull, and re-set a post on the same visit, because we know that in 76053 especially, a simple hinge or latch call often turns into a post reset. We have learned to price it as a near-automatic line item on any hinge or latch repair in those blocks, and we tell you that up front, before the work starts.
We reset and re-plumbed a badly racked swing gate on a 1960s ranch in Hurst’s 76053 area after the clay heaved both hinge posts. The original ornamental iron panel was still solid, but the pintles were worn egg-shaped and the latch strike no longer aligned. Our crew pulled both posts, poured new concrete footings at a depth below the active clay zone, then welded new hinge barrels and installed a fresh latch. The gate now swings true, and the post footing is sized to ride out the next wet-dry cycle.
The lesson from that job applies to most older gates in Hurst. The ironwork itself is often worth saving. What fails first is what is underground, and what wears second is what connects the gate to the ground. Fix both, and a 60-year-old gate closes like it did the day it was hung.
Key Takeaways
- Hurst’s expansive clay soil is the single biggest driver of failing gate posts across 76053 and 76054. Post reset with deep footing is the permanent answer.
- Most sagging gates in Hurst do not need new panels. They need new hinge barrels welded onto their original posts.
- Legacy operators without modern entrapment protection are common on older Hurst properties. Retrofits are usually possible, and we tell you when they are not.
- Ironworks Gate Co. quotes every job before work starts, guarantees it for 90 days in writing, and answers the phone live, 24/7.
Schedule Your Gate Parts & Welding Service in Hurst
If your gate is sagging, binding, or simply worn out, give us a call. We serve Hurst from our Dallas-Fort Worth dispatch office and keep crews in the area every week. You will talk to a live person, get a straight answer, and have a free estimate from Victor Salinas’s team before any work begins. Call (817) 580-8494 now, or call us day or night. We answer when we say we will, and we stand behind every weld.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Hurst and surrounding communities for over 42 years.