Linear Hinge & Roller Replacement Nationwide

Linear Hinge & Roller Replacement: The Southlake Owner’s Guide

We stock and install Linear-compatible hinge and roller replacements for Southlake homeowners, with most jobs running $240 to $490 installed and finished the same day we arrive. If your gate drags against the ground, swings with a groan, or sags visibly at the latch end, the hinge or roller is the usual culprit. This page covers what fails first on Linear-equipped gates, what replacement actually costs in the Southlake market, and how to know whether you’re buying the right part before anyone turns a wrench.

Call (817) 580-8494

Most Southlake owners discover a failed hinge or roller the same way: the gate worked fine for eighteen years, then one afternoon it didn’t. The gate starts catching on the concrete, the opener starts laboring harder than it should, and eventually the safety sensor trips or the motor throws a fault code. What was a $20 part six months ago is now a binding gate and a burned-out gearbox. Catching it early costs a few hundred dollars. Catching it late costs an opener.

Which Linear Models This Applies To

Linear hinges and rollers are not one size fits all, and this is where we see a lot of wasted money. Linear built swing-gate hardware across three main series lines: the older LS series with bolt-on steel hinges, the APeX swing series with adjustable bearing hinges, and the current-generation units using sealed cartridge rollers on a steel track. The hinge or roller that fits a 2006 Linear swing unit will often not match a 2022 APeX, even though both say Linear on the motor cover.

Before calling, check the metal tag on the opening arm or the control box. The model number usually begins with LS, APeX, or MU. If the tag is faded and unreadable, measure the hinge bolt centers with a tape measure and note whether the roller rides on a V-track or a flat rail. We carry OEM Linear replacement parts for current models and quality aftermarket equivalents for discontinued series where Linear no longer supplies them. Aftermarket is fine when the steel gauge and bearing spec match the original. Cheap zinc-alloy hinges from big-box stores are not fine, and we see them fail inside two years on a Texas summer.

One compatibility gotcha specific to Linear swing units: the hinge shoulder bolt is a 5/8-inch diameter on LS series but 3/4-inch on late APeX units. Anyone who tries to force the wrong bolt has stripped the threads before the hinge is even seated. We match the part to the model before we leave the shop.

Signs Your Linear Hinge & Roller Replacement Is Failing

• The gate sags at the opposite end from the hinge post. This means the hinge bushings or the hinge itself has worn enough to let the gate frame settle. A gate that has dropped half an inch will only keep dropping, and the opener is fighting gravity every cycle.
• The gate scrapes or leaves a fresh mark on the driveway. The roller beneath the gate has either seized or lost its rubber jacket. Once the roller stops rolling, the gate grinds against concrete on every swing, and the tire marks you’re seeing are melted rubber and steel.
• You hear a dry creak or metal-on-metal squeal near the hinge post. The hinge bearings are dry or seized. Adding grease buys a few days; replacing the hinge buys another fifteen to twenty years.
• The opener sounds labored, like a truck in the wrong gear. The motor is working against a binding hinge or a flat roller. Linear openers are durable machines, but a year of grinding against a bad hinge will finish the gearbox on even the best unit.
• The gate jerks or stutters mid-swing. That is a roller catching on a flat spot, then releasing. The gate is not moving smoothly, and the safety sensor may intermittently reverse the gate for no visible reason.

Replacement Cost & What’s Included

In Southlake, Linear hinge and roller replacement runs $240 to $490 installed, depending on whether we’re swapping a single roller or the full hinge set and whether the gate needs a sag adjustment after the new parts are on. Here is how the numbers break down for a typical single swing gate:

• Single roller replacement: $85 to $140 parts and labor
• Single hinge replacement: $110 to $185 parts and labor
• Full hinge and roller set, one gate: $240 to $310 parts and labor
• Both gates on a double driveway, full set: $380 to $490 parts and labor

What drives the range is access. A gate over a concrete apron with the hinge post intact is straightforward. A gate hung on a rotted wood post or sitting on ground that has shifted takes longer, and we level the gate along with the part swap. Every price is quoted and agreed in writing before we touch a bolt, and every job is protected by our 90-Day Done Right Promise, written on the invoice, no argument, no paperwork chase. If it is not right, we come back and make it right.

DIY or Call Us?

What an owner can safely check: whether the roller spins freely by hand, whether the hinge bolts are visibly loose, and whether the gate has dropped against the latch plate. That takes ten minutes and tells us a lot over the phone. What we caution against: pulling a gate off its hinges without lifting support. A full-size steel gate can weigh 300 to 500 pounds. Once the hinge bolts are out, that weight has to go somewhere, and it will go somewhere fast.

We’ve had Southlake customers ask us to finish a hinge swap a neighbor started on a Saturday. The hinge pin was driven halfway out with the gate still hung. It bent, the gate twisted, and the job cost twice what it would have if no one had touched it. If the gate is heavy or the post looks questionable, call (817) 580-8494 first. The estimate is free, and we’ll tell you honestly whether the job needs two hands or a shop truck.

FAQs