Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterDoorKing Gate Parts & Welding in Southlake: What to Know First
We provide independent DoorKing gate parts and welding service across Southlake, TX, with most hinge replacements, post repairs, and roller swaps completed the same day we show up. A straightforward DoorKing hinge or latch repair in Southlake typically runs $275 to $600, while full post replacement or custom welding work lands higher, and you’ll get a firm written price before we turn a single bolt. If you own a DoorKing slide or swing gate and the metal is sagging, binding, or tearing, call (817) 580-8494 and we’ll tell you honestly what it needs.
This page is for Southlake homeowners with a DoorKing gate that’s starting to show its age at the hinges, posts, rollers, or latch points. Victor Salinas and the Ironworks Gate Co. team have been doing this work in the area long enough to know how a Southlake summer and a DoorKing gate argue with each other.
How DoorKing Products Fail and How We Fix Them
DoorKing builds dependable openers, but the steel they hang on takes a beating in Texas weather and Southlake soil. These are the failures we see most often on DoorKing jobs in the area:
- Hinge weld fatigue on the DoorKing 6002/6003 slide gate frames. A slide gate doesn’t pivot, so homeowners assume the hinges are safe. The reality is different: the frame flexes every cycle, and after a decade the hinge welds crystallize and crack. We cut out the old weld, bevel the joint, and lay a full-penetration weld meant to outlast the rest of the gate.
- Post rot and electrolysis at the base plate. Southlake’s clay soil holds moisture against steel posts through the wet season, and DoorKing’s powder coat eventually lets water wick into the post base. By the time a gate sags an inch, the post wall is usually thinned from the inside. We remove the post, core the footing, set a new post in place, and weld a base plate with drainage clearance so water has a way out.
- Rail wear and camber loss on long DoorKing slide runs. A 20-foot slide gate carries serious weight on the top rail. When the rail sags mid-span, the chain or belt picks up slack and the opener works harder. We straighten or replace the rail, re-camber it slightly upward, and re-weld the pickets to restore a true line.
- Latch and lock misalignment on DoorKing pedestrian gates paired with swing operators. The DoorKing 9000 series swing arm is strong enough that an out-of-square latch gets slammed out of alignment within weeks. We re-square the frame, replace the latch with a heavier model when needed, and adjust the strike so the lock engages without fighting the operator.
- Roller seizure on bottom-track DoorKing slide gates. The OEM rollers DoorKing ships are fine for a clean, level track. On Southlake driveways with slope or aggregate, rollers wear oblong and seize. We install sealed-bearing aftermarket rollers with a higher load rating, which typically buys several extra years of quiet operation.
Our DoorKing Gate Parts & Welding Process
Every job follows the same order of work, whether it’s a hinge replacement or a full post rebuild. You know the cost before we start, and you know what we found before we fix it.
- 1
The call. A live person answers at (817) 580-8494, day or night. You describe the symptom, we ask about the gate’s age, length, and DoorKing model, and we schedule the visit.
- 2
Diagnostics at the gate. We measure the gap, check the weld seams, roll the gate by hand, and test the operator’s pull. Victor often finds the root cause is two feet from where the symptom shows.
- 3
The parts decision. If the original DoorKing part is available and reasonably priced, we use it. If it’s backordered or price-inflated, we tell you, and we offer a proven aftermarket equivalent that we’ve put on dozens of Southlake gates without a callback. The choice is always yours.
- 4
The repair. We cut, weld, grind, and paint with care taken to match the existing finish as closely as possible. Our welds are full-penetration, not tacked for show.
- 5
The test. We cycle the gate 20 to 30 times, check the operator’s force settings, and listen for strain. If it doesn’t close like it did when it was new, we keep working.
- 6
The guarantee. Every job, every visit, covered by our 90-Day Done Right Promise in writing. No forms, no arguments, no exceptions.
What DoorKing Gate Parts & Welding Costs in Southlake
These are the price ranges we quote most often on DoorKing gates in Southlake. Your exact cost depends on gate size, steel thickness, and what the excavation reveals once we open the post footing.
- Hinge replacement (weld-in, per hinge): $275-$450 installed, including cutting out the old hinge, surface prep, and paint match.
- Post replacement (single post, set in concrete): $600-$1,200 depending on depth, diameter, and whether the footing needs re-pouring.
- Rail repair or replacement (per 10-foot section): $450-$850 including straightening, re-camber, and weld time.
- Custom welding (reinforcement plate, picket splice, decorative repair): $150-$400 typically, with a clear time-and-material rate quoted up front.
- Gate roller replacement (set of 2-4): $180-$380 including sealed-bearing rollers and track alignment.
- Latch and lock replacement on a DoorKing pedestrian gate: $200-$450 depending on lock grade and strike fabrication.
The price we quote is the price you pay. If we open up a post and find the footing cracked, we stop and show you before doing anything else. Call (817) 580-8494 for a free estimate on your DoorKing gate repair in Southlake.
Why Southlake Homeowners Call Ironworks Gate Co. for DoorKing Work
We’ve been doing gate work since 1984, and around Southlake we’re the company that shows up when we say we will, in uniform, background-checked, and ready to work the way we’d work on our own mothers’ driveways. DoorKing is one of nine gate-automation brands our techs are trained and equipped on, along with LiftMaster, Mighty Mule, and Ghost Controls, so whatever opener sits on your gate, the diagnosis is right the first time.
Most DoorKing parts and welding jobs are done in one visit. And when we leave, you get the 90-Day Done Right Promise in writing. Not a verbal “call us if anything’s wrong” but a real guarantee that says if it isn’t right, we come back and make it right. No fine print, no papers to sign, no debate.
Our standing offers apply to every DoorKing job: $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a permanent 5% discount for seniors and veterans. A gate that works right doesn’t need to announce itself.
FAQs
Yes. As an independent DoorKing service provider, we weld and replace structural gate parts on DoorKing-equipped gates in Southlake all the time without affecting your opener warranty, because the warranty covers the operator and control board, not the gate steel. We keep our work on the metal side and never modify the opener’s internal components during a parts and welding job.
Most hinge, roller, and latch repairs in Southlake are scheduled within one to three business days, and the work is usually done the same day we arrive. If the gate is stuck open or won’t close and your property is exposed, tell us when you call and we’ll prioritize the visit. Call (817) 580-8494 and a live person will give you an honest arrival window.
We use OEM DoorKing parts when they’re available and fairly priced, and we’re honest with you when they’re not. For structural components like rollers, hinges, and latch hardware, we often recommend aftermarket parts that meet or exceed the original spec and cost less, and we’ve put them on enough Southlake gates to stand behind them with the same 90-Day Done Right Promise.
In Southlake, a gate with surface rust at the hinges is usually repairable. What matters is the thickness of metal remaining at the hinge post and frame. We measure it on-site. If the steel still has integrity, we cut out the rusted section and weld in new material. If the post wall is thinned past the point of holding a weld, we tell you straight and quote replacement without pushing you either way. Call (817) 580-8494 and we’ll give you an honest assessment for free.
If any weld we made, part we installed, or repair we performed fails within 90 days, we come back and fix it at no charge. No forms, no arguments, no fine print. We’ve been doing this long enough to know that a weld done right will outlast the gate around it, and we put that belief in writing.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Southlake and nearby areas.