Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Motor & Opener in Southlake: What to Know First
Independent FAAC gate motor and opener service in Southlake runs through Ironworks Gate Co., and most repair jobs are completed in a single visit. A typical FAAC repair on a swing or slide gate in this area lands between $285 and $740 depending on the failed component, and the price is quoted and agreed before any work starts. If your FAAC operator is making noise but not moving the gate, or the gate drifts after closing, this page covers what is actually going on and what it costs to set it right.
This page is for the homeowner who owns a FAAC operator and wants a straight answer, not a sales pitch. Call (817) 580-8494 and a live person answers. Victor Salinas and our technicians have been working on FAAC equipment in Southlake driveways long enough to know what fails, why it fails here, and when repair is the honest call instead of replacement.
How FAAC Products Fail - and How We Fix Them
- FAAC 400 and 402 operators losing position in Southlake heat. The hydraulic operators on older FAAC 400-series swing gates run warm in August, and the internal bypass valves wear faster here than they do in cooler climates. The symptom is a gate that opens fine at 7 a.m. and then stalls or drifts at 3 p.m. The fix is usually a bypass valve replacement and fresh hydraulic fluid, not a new operator. We see this on gates along Continental Boulevard and in the older estates off North Carroll Avenue every summer.
- FAAC 750 and 760 slide operators eating limit switches. These slide operators use mechanical limit switches, and the fine silt that blows through Southlake lots works its way into the switch housing. The gate stops a foot short, or over-travels and slams the end stop. We replace the switches with sealed units and adjust the ramp-down so the gate does not hammer itself. This is a $140-$220 fix, not a new motor.
- FAAC E024U control board capacitor failure after storms. The E024U board is the brain on many FAAC swing operators installed in the last decade. North Texas thunderstorms bring voltage spikes, and the board’s capacitors take the hit. The board goes dark, or the gate opens but will not close on auto. We test the board before condemning it. If the capacitors are cooked, we replace them at the component level when practical, or install a factory board with a surge protector wired in line. That surge protector is the difference between doing this once and doing it every other spring storm season.
- FAAC hydraulic pump motors that hum but do not build pressure. On the 415 and 770 models, a pump motor that hums is usually not a dead motor. It is a set of worn seals or a clogged inlet screen starving the pump. We pull the pump, clean or reseal it, and bench-test it before quoting any motor replacement. More than half the humming FAAC pumps we see in Southlake do not need a new pump, they need a reseal kit and clean fluid.
- FAAC photocell and safety-edge faults that stop the gate dead. FAAC operators are particular about safety inputs. A photocell misaligned by a lawn mower bump, or a safety edge with a nicked wire, will put the operator into fault and the gate will not move at all. The owner assumes the operator is dead. We trace the fault to the sensor, not the motor, and most of these calls are resolved the same day for the cost of a service call plus parts.
Our FAAC Gate Motor & Opener Process
- 1
Call and describe the symptom. A live person answers at (817) 580-8494. We will ask what the gate does, what it will not do, and whether the operator hums, clicks, or stays silent. That tells us which spare parts to bring so we are not wasting your time with a second trip.
- 2
On-site diagnosis. A uniformed, background-checked technician arrives when promised, opens the operator, and tests the board, motor, pump, limit switches, and safety inputs in that order. We explain what we find before we touch a tool.
- 3
Upfront price, no surprises. You get a written price for parts and labor before any bolt is turned. We quote OEM FAAC parts when the warranty or board replacement calls for it, and quality aftermarket only when it is the smarter long-term move. We will tell you which is which and why.
- 4
The repair. We fix what failed and only what failed. No add-ons, no invented problems, no charging for work a gate does not need. That is how Victor has run this company since he started working on gates around Southlake.
- 5
Test the full cycle and the safety circuits. We run the gate through open, close, obstacle detection, and auto-close timing. In Southlake, we also verify the operator’s thermal behavior on a hot afternoon because a gate that works in the shade and stalls in direct sun is not fixed.
- 6
Clean up and write down the guarantee. The work site looks like we were never there, and you get the 90-Day Done Right Promise in writing. If it is not right, we come back and make it right. No paperwork, no arguing.
What FAAC Gate Motor & Opener Costs in Southlake
- Service call and diagnosis: $89-$139, credited toward the repair if you proceed the same day.
- Limit switch replacement on a FAAC 750/760 slide operator: $140-$220.
- Hydraulic bypass valve and fluid service on 400-series swing operators: $210-$340.
- FAAC E024U control board replacement with surge protection: $380-$610.
- Hydraulic pump reseal and bench test: $240-$410. A full pump replacement, when truly needed, runs $520-$780.
- Complete FAAC operator replacement (mid-range swing, installed): $1,400-$2,600 depending on gate weight and access.
What moves the price on a FAAC job in Southlake is parts availability, the age of the operator, and whether the problem is mechanical, hydraulic, or board-level. Older FAAC 400-series parts are still available, but some are special-order. We will tell you the honest repair-versus-replace math and never push a replacement when a reseal kit does the job. Call (817) 580-8494 for a free estimate on any FAAC gate motor or opener work.
Why Southlake Homeowners Call Ironworks Gate Co. for FAAC Work
We have been serving Southlake and the surrounding area for over 42 years, and we plan to be here answering the phone for another forty. Every FAAC repair we complete is covered by the 90-Day Done Right Promise, written and no-hassle. If it is not right, we come back. No arguing, no fine print, no “that’s wear and tear.”
Our techs are trained on nine gate-automation brands, so when we walk up to your FAAC, we are not guessing. And because we also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, we can tell you straight when staying with FAAC is the right call and when a different operator would serve your gate better than another FAAC repair. Most FAAC jobs are completed in one visit. A live person answers the phone 24 hours a day, every day.
FAQs
Yes. Most FAAC 400, 402, 415, 750, and 760 series parts are still available, though some older hydraulic components are special-order and take a few business days. We inventory the common failure parts, including limit switches, bypass valves, capacitors for the E024U board, and reseal kits, so most Southlake repairs happen the same day we show up. Call (817) 580-8494 with your model number and we will confirm availability on the spot.
No. As an independent FAAC service provider, we work on operators still under manufacturer warranty as well as units long out of warranty. If your FAAC equipment is under warranty, we will help you determine which components are covered and handle the repair accordingly. What we will not do is pretend to be a factory-authorized dealer. We are not, and we will tell you that plainly before any work begins.
The honest answer depends on the operator’s age and how the hydraulic or board components have held up. FAAC hydraulic operators, particularly the 400 and 415 series, are repairable for many years because the core is simple and durable. If your board and pump are sound, a $300 repair keeps the operator running for years more. If the pump is scored, the board is failing, and the limit switches are worn, replacement starts making better sense than stacking repairs. We will tell you which camp your operator falls into before any money changes hands.
Most FAAC repair calls in Southlake are scheduled the same day or the next morning. A live person answers at (817) 580-8494 around the clock, so you are never leaving a voicemail while your car sits trapped in the driveway. We carry the most common FAAC failure parts on the truck, which is why most jobs are done in one visit.
Yes. We wire FAAC operators into existing intercom and access control systems, and we install and service battery backup on FAAC swing and slide operators. Southlake loses power during spring storm season, and a battery backup keeps your gate operating when the lights are out. We can assess your FAAC’s power draw and spec the correct backup for your gate’s weight and cycle count.
Call Ironworks Gate Co. for FAAC Gate Motor & Opener in Southlake
If your FAAC is making noise, stopping short, or refusing to move, call (817) 580-8494. We will tell you what is wrong, what it costs, and whether it is worth fixing, before you spend a dollar. A gate that works right does not need to announce itself, and neither does a gate company. We will be there when we say.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Southlake and nearby areas.