Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Hurst
Gate access control in Hurst means keypads, remote receivers, phone entry, card readers, and video intercoms on gates that have to keep working through Tarrant County clay heave and hundred-degree summers. We replace, retrofit, and program access systems on gates of every age, from original 1960s ornamental iron to modern steel driveways across 76053 and 76054. Most access control calls in Hurst are diagnosed and repaired in a single visit. Call (817) 580-8494 and you’ll get a live person, not a voicemail tree, any hour of the day or night.
We’re Gate Access Control specialists, not general handymen. Hurst has its own set of gate problems, and they usually start in the ground, not in the control board. That’s the difference a local specialist brings.
Why Ironworks Gate Co. Is Hurst’s Preferred Gate Access Control Company
We’ve been called out to Hurst homes for over four decades to fix what other companies installed wrong or couldn’t find at all. The work is led by Victor Salinas, and every Hurst job is governed by the same Keystone Standard we’ve applied since the company was founded: a written 90-Day Done Right Promise on every completed job. If it isn’t right, we come back and make it right. No paperwork, no arguing, no exceptions.
Hurst homeowners rarely shop for the lowest bid. They want the gate and its access system working quietly and dependably for years, and they want a company that answers the phone when something fails at 9 p.m. on a Sunday. That’s who we are. A live person answers every call, 24/7. Dispatch is coordinated from our Dallas-Fort Worth office, and techs serve Hurst locally with background-checked, uniformed crews.
We know that a keypad mounted on a gate post set in Hurst’s black clay is only as good as the footing under it. This local knowledge sets us apart from out-of-town installers who bolt on a keypad and leave before the next rain.
Our Gate Access Control Services in Hurst
Every Hurst gate is different, from a single chain-link pedestrian gate in a 1955 ranch side yard to a custom ornamental iron driveway gate on a larger lot near Colleyville. The access system has to match the gate’s weight, swing, and mounting surface, and it has to survive Tarrant County soils and summers. Here’s what we handle across Hurst.
Keypad Entry
Keypad entry is the most common access system on Hurst driveways, especially on mid-century homes where a wired intercom wasn’t part of the original build. We install new keypads, replace worn-out buttons and housings, and program multiple entry codes for family, guests, and service people. A keypad on a Hurst gate has to be mounted so the housing stays plumb and the latch lines up even when the post shifts slightly with the season. We check the footing before we mount the keypad, because in 76053 and 76054 that’s where the problem usually begins.
Remote Control
Remote controls and receivers still handle most daytime traffic on Hurst driveways. We program remotes, add receiver modules to older operators, and replace failing antenna units on systems where range has dropped to a few feet. Many of the original operators in Hurst homes are still functioning but the remotes are twenty years old and the receiver boards are tired. We can often restore full remote range without replacing the operator itself.
Phone Entry
Phone entry systems let a homeowner answer the gate from a cell phone or house phone and buzz a visitor in without carrying a remote. This works well on Hurst properties where visitors, delivery drivers, and lawn crews need occasional access. We install phone entry modules that tie into existing gate operators, and we configure the call routing so it rings the right number on the first try. On Hurst’s older swing gates with fabric that racks, the phone entry unit must be mounted off-gate on a stable post so it doesn’t lose power when the gate flexes.
Card Reader
Card readers are common on Hurst properties where multiple people need regular access: family members, caretakers, pool service, landscapers. We install proximity readers, key fob systems, and card-based access tied to the gate operator. Cards can be added or deleted without rewiring. For older Hurst gates with worn hinges, we always check the gate’s swing arc before finalizing the reader position, because a gate that racks even half an inch can throw the reader’s alignment with the strike.
Video Intercom
Video intercom is the strongest upgrade we install on Hurst homes with mid-century gates. A visitor presses the call button, and the homeowner sees and speaks with them from a phone or indoor monitor before opening the gate. We retrofit video intercom onto existing iron gates without replacing the gate itself. On a 1960s ornamental gate with rusted mounting plates, we fabricate a new plate and weld it in so the intercom housing sits solid, level, and weather-tight. For Hurst homeowners who plan to stay in their home for another twenty years, a video intercom on a heavy bespoke gate is one of the most useful security additions they can make.
Smart Access
Smart access means opening and monitoring the gate from a phone app, receiving alerts, and granting temporary access codes that expire. We add smart modules to existing operators, including older DoorKing units, so Hurst homeowners don’t have to replace a working operator just to get app control. Smart access makes sense when you’re not always home to answer the gate, or when you want a log of who came and went.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Hurst
Our techs are trained and equipped on nine gate-automation brands, and in Hurst we see a lot of BFT, Linear, and Ghost Controls equipment on driveways, plus plenty of legacy Viking units. That breadth matters because a mid-century Hurst home may have had three operator changes since the 1980s, and each installer may have used a different brand. We diagnose and repair whatever is on the driveway, on the first visit, without telling you to replace a whole system because we don’t carry the part. We stock common boards, remotes, and safety components for the brands Hurst homes actually use.
Common Gate Access Control Problems We See in Hurst Homes
- Keypads and card readers that fail after rain. Tarrant County’s expansive black clay swells after a soaking, pushing gate posts one to two inches out of plumb within 24 hours. A keypad mounted on the gate lands out of alignment with the strike, and the operator short-cycles. The fix starts with the post footing, not the keypad.
- False obstruction trips on 50-year-old swing gates. Original mid-century iron gates with worn pintles and failing welds rack under daily use. The operator’s limit switches read that racking as an obstruction and leave the gate half-open, or reverse it mid-cycle. We replace the hardware or re-weld the frame so the access system doesn’t fight the gate.
- Video intercom power cutting out intermittently. Summer heat above 100°F accelerates rust on ungalvanized iron, loosening the mounting plate behind the intercom or phone entry module. The unit loses power intermittently. We fabricate a reinforced plate and restore solid contact to the board.
- Old operators with no app control. Many Hurst homes still run reliable operators with keypad-only access. Retrofitting smart access is usually possible without replacing the operator, which saves a homeowner thousands and keeps a proven unit in service.
In Hurst’s 76053 and 76054 ZIP codes, we start every access control install with a post footing check before we even open the keypad housing. If the post moves, the access system will fail, no matter how good the keypad is. Our crew recently reset a sagging swing gate on a 76053 ranch home where the original 1960s iron hinge post had leaned three degrees into wet clay, throwing the DoorKing keypad entry off-level and causing the gate to bind against the latch. We poured a deeper post footing, re-plumbed the hinge post, and remounted the keypad and safety photocell so the operator cycles without racking the panel.
Pricing for Gate Access Control in Hurst, TX
A keypad replacement in Hurst typically runs $250 to $450 including the unit and labor. A new remote receiver added to an existing operator runs $180 to $320. Phone entry systems start around $450 and go up to $900 depending on call routing and existing wiring. Video intercom retrofits on existing Hurst gates fall between $1,200 and $2,800, with the spread driven by whether we’re fabricating a new mounting plate, running new low-voltage wiring, or working around masonry pillars. Smart access retrofits run $350 to $800 for most operators.
Every price is quoted and agreed before any work starts. The number on the invoice is the number on the quote. We offer a $50 discount on any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a permanent 5% senior and veteran discount. Call (817) 580-8494 for an exact quote. Estimates are free.
We Also Serve Cities Near Hurst
Ironworks Gate Co. serves gate access control needs across the Mid-Cities, including Bedford, North Richland Hills, Colleyville, and Euless. If you live near the Hurst city line, give us a call and we’ll tell you straight whether we can handle your gate in a single visit. Most of the time the answer is yes.
Serving Hurst, TX - Our Local Coverage Area
We’re based in the Hurst area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Hurst
Tarrant County black clay swells after a heavy rain and pushes gate posts out of plumb, usually within a day. The keypad, mounted on the gate, shifts out of alignment with the strike and the operator reads it as an obstruction or a failed latch. The fix is a post footing adjustment and re-mounting the keypad level, not replacing the keypad. Call (817) 580-8494 and we’ll check the footing first.
Yes. We fabricate and weld a new mounting plate onto the existing iron gate, run the low-voltage wiring, and mount the intercom housing solid and weather-tight. The gate stays. The access gets better. Estimates are free.
Yes. A safety photocell is required on any powered gate, and it protects against the gate closing on a child, pet, or delivery driver. On Hurst clay, the photocell alignment also needs re-checking after wet seasons because the gate path can shift. We include photocell alignment in every access control service call.
Usually, yes. We add a smart access module that talks to the existing operator’s open-command input, so you get phone app control, alerts, and temporary codes while the DoorKing keeps doing its job. The operator stays in place. Call (817) 580-8494 for a free estimate on the retrofit.
For Hurst’s expansive clay, a gate post footing should extend below the active clay zone, typically 30 to 42 inches deep depending on gate weight and post size. We pour wider and deeper footings than the original 1960s work did, which is why our access systems stay aligned through the wet-dry cycle. A shallow footing is the single biggest cause of keypad and latch failure in 76053 and 76054.
Call Ironworks Gate Co. for Gate Access Control in Hurst
If your Hurst gate’s keypad, intercom, phone entry, or remote isn’t working the way it should, call (817) 580-8494. You’ll get a live person, a straight answer, and a free estimate. We’ll send a background-checked, uniformed technician who knows Hurst’s gates, Hurst’s clay, and the right way to keep a heavy gate running quietly for years. Done right, and backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Hurst and the Mid-Cities for over 40 years.